VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit deposit steps guide
starter vape kits · dropshippers

Starter Vape Kit deposit steps guide

Starter Vape Kit sits in a crowded price band, and the cheapest quote on the sheet is rarely the cheapest unit on your shelf. Everything below is built around reorder rate, defect rate and cash conversion rather than headline unit price.

Published 29 May 2025  ·  VapeWholesaleHub  ·  Reading time 5 min

Starter Vape Kit deposit steps guide configuration from a production run, photographed before packing.
Starter Vape Kit deposit steps guide configuration from a production run, photographed before packing.
Carton-ready units from the same batch, coded for traceability.
Carton-ready units from the same batch, coded for traceability.

Getting the documents right

We ship starter vape kits to distributors, chain buyers and independent shops. What follows is the material we normally cover in a first conversation: what we hold in stock, how we test it, how it ships, and what happens when a carton arrives damaged.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

We keep batch codes traceable from carton to production date. When a market authority asks for traceability, a supplier who cannot produce it in an hour becomes a liability very quickly.

Sell-through notes for the shop floor

Bundle a device with a consumable and the reorder rhythm changes from occasional to weekly. That single merchandising decision often does more for monthly revenue than a price promotion.

Shelf position decides velocity as much as price. Keep starter vape kits at eye level, one facing per SKU, and rotate the trial line every quarter so the display keeps earning attention.

For dropshippers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

What happens when something goes wrong

Every account gets a named contact who has actually seen the product. Being passed between three people to answer one question about a coil resistance is the fastest way to lose a buyer, so we do not organise support that way.

The replacement policy is deliberately simple: report within seven days of delivery with photos and the batch code, and we replace or credit at the next shipment. We do not argue about a defect we can see in a photograph.

  • Reference sample retained from every batch
  • Mixed SKU cartons to spread first-order risk
  • Artwork proof plus physical dummy for custom packaging
  • Batch codes traceable from carton back to production date
  • Cartons drop-tested and pallet-counted for clean freight
  • Private label files archived for future rebrands

The checks behind every shipment

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

Specification summary

Typical specification for this category
Battery350 mAh
Pod capacity3.0 ml
Coil resistance1.0 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order300 units per SKU, mixed cartons allowed
Lead time30 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

What is the minimum order for starter vape kit?

Standard configurations start at 60 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 240 units because of setup time on the line.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

How long does production take?

Around 30 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us